This turn signal and headlight dimmer switch is located on the left side of the steering column. It controls the low / high beam function as well as the left / right turn signal function. These fail commonly as our classics age and should be replaced as soon as issues arise. Be sure to check the right-side washer switch as well, now is the time to replace to save on labor costs, part # 91161330602 high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please...(choose a part on the right to read more)

View/Change Diagram

911 1974-77 - Electrical

Cheaper alternative to the expensive 70 71 turn signal switch. these 70-71 switches are not easy to install and require soldering and heat shrink tubing

This turn signal and headlight dimmer switch is located on the left side of the steering column. It controls the low / high beam function as well as the left / right turn signal function. These fail commonly as our classics age and should be replaced as soon as issues arise. Be sure to check the right-side washer switch as well, now is the time to replace to save on labor costs, part # 91161330602 high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: technically this can fit the 1974-1975 911 models, but if you want the original look, please order part # 91161330...(choose a part on the right to read more)

View/Change Diagram

911 1974-77 - Electrical	911 1978-83 - Electrical
911 1984-86 - Electrical	911 1987-89 - Electrical
930 1975-77 - Electrical

This is a sleek, light-weight, multi-directional light that clips on your hat or any other object. It gets it’s illumination from either 2 or 4 high-powered led lights (switchable based on how much light you need) that provide a clean crisp light. Able to tilt and turn 360 degrees, this light makes it easy to brighten up whatever task you are working on.

General Fitment

Tried to dismantle your pedal cluster to install new bushings and found that it is impossible to drive out the roll pin? Join the crowd! Time for a rebuilt cluster. All of our rebuilt clusters are completely dismantled, sand-blasted, painted, new parts used if needed, and reassembled with silicone bronze bushings. the only complete cluster available from anywhere! Includes brake light switch, brake push rod, throttle pivot, and rubber pedal pads. Ready to be installed! core charge...(choose a part on the right to read more)

General Fitment

Kit includes everything for performing hundreds of automotive diagnostic and mechanical tests. Used for one-person brake bleeding, produces vacuum or pressure at the turn of a switch. Comfortable ergonomic design with one-finger trigger vacuum/pressure release. Durable die-cast metal construction for long life. Pressure and vacuum are created on the squeeze stroke for superior accuracy and control.

Includes:
• silverline elite hand vacuum/pressure pump with 2" (50 mm) compound gauge with rubber boot
• 4.5 oz. (135 ml) fluid reservoir bottle with fluid transfer and storage lids
• 4 tapered adapters for connecting to tubing from .09" (2.3 mm) to .50" (13 mm) id
• 2 tapered manifold plugs
• 4 ...(choose a part on the right to read more)

General Fitment

Battery switch that allows you to disconnect all battery functions with the simple turn of the removable key. Perfect for racing and motorsports applications. The battery master cut off switch also includes a fused link to allow low drain items like clocks and radios to draw a small current to keep them on. Installation instructions are included. Sold individually.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This is a genuine smarttop product that includes these features: simply open or close your convertible top using the original factory remote control key fob. The one-touch convertible top operation allows you to open or close the top with one touch. Turn the module off with an easy key sequence. Ideal when letting someone else drive your car. Turning the ignition on or off does not interrupt convertible top operation. One-touch and auto operation for the wind deflector can be programmed. The module can be removed any time, simple to return a leased vehicle or to sell it in original condition. One-touch operation of all windows via the driver's door switches. Custom designed plug-in-between wiring harness for e...(choose a part on the right to read more)

Our 911 sanden kits offer many benefits over the original york compressor found on the early 911 and 930 up through 1983. The sanden uses a "wobble-plate" to move five smaller pistons as compared to the york that uses a crankshaft to move two large pistons. The sanden wobble-plate design requires less horse power to turn and is a better match for the condenser area. Our sanden kit uses less engine compartment space and less horse power to turn. You will notice it runs smoother and quieter and improves system efficiency. The sanden compressor and it's mounting bracket bolt directly to the original york sub-plate. You can purchase our sanden kits in four configurations to match your objectives and budget: from...(choose a part on the right to read more)

General Fitment

This item is required by most organized race events. Remote pull kits allow corner worker to easily turn the power off on your car in the case of an emergency. This kit has a loop end that can easily be installed through body seams, eliminating the need to drill holes. Kit can also be mounted in dash for easy driver access. Includes 6' red pull cable, mounting bracket, cable end and full installation instructions. Can be used on several different battery disconnect switches.

General Fitment

This item is required by most organized race events. Remote pull kits allow corner worker to easily turn the power off on your car in the case of an emergency. This kit has a t-handle end that can easily be installed through existing or drilled holes. Kit can also be mounted in dash for easy driver access. Kit includes 6' red pull cable with handle, power/ off tag, cable end and full installation instructions. Can be used on several different battery disconnect switches and all rennline kill switches. Red shown

General Fitment

This 6 pole cut off switch is the same style used in the factory Porsche cup cars. It has been designed to eliminate the possibility of the alternator circuit being damaged due to a heavy voltage surge that can occur with the use of a heavy duty single circuit on/off switch. When turned to the off position the engine will be automatically stopped due to the secondary switch function whereby the ignition is cut. This prevents engine 'run on' and is a vital safety factor especially in competition use. This switch is also a very simple and effective anti theft device for cars, trucks, boats and ag, vehicles.

-12-24 volt
-prevents battery drain
-3 ohm 11 watt resistor for controlled earth leakage
-fully re...(choose a part on the right to read more)

General Fitment

Easily installed on the side of the transaxle test by removal and insertion of a small pick. if the reverse lights operate (make sure the key is turned on) then the reverse light pin is worn.

View/Change Diagram

356 1960-65 - Transmission	911 1970-73 - Transmission
911 1970-73 - Transmission	911 1970-73 - Transmission
911 1974-77 - Transmission	911 1978-83 - Transmission
911 1978-83 - Electrical	911 1984-86 - Transmission
911 1984-86 - Electrical	911 1987-89 - Transmission
911 1987-89 - Transmission	930 1975-77 - Transmission
912 1965-69 - Transmission	912 1965-69 - Transmission
912 1965-69 - Electrical	928 1978-82 - Transmission
928 1983-86 - Transmission	928 1987-91 - Transmission

Perfect fit turn signal switch for all 70 and 71 Porsche 914 models. Not the easiest switch to install, require soldering!

This model is the first of a brand new product line for perma-tune. We have combined our accumulated knowledge of Porsche ignition over the last 48 years and applied it to the very latest electronics technology to produce a state of the art electronic ignition module that is period correct looking. Made to look like an old school electrical relay, it blends right into the engine bay of a 356 or an early 911. No crimps, no mess, no headaches plug and play features eliminate the need for wire crimps and complicated wiring diagrams. Wires are cut and stripped, then inserted into the wire bus for a secure, plug in connection without the need for special tools or wire crimps. Simple, four wire installation. There is...(choose a part on the right to read more)